Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:manuals:service-notes-for-mitail [2026/06/06 15:01] – darkgrueen:manuals:service-notes-for-mitail [2026/08/02 16:41] (current) – darkgrue
Line 55: Line 55:
 ===== Installing Batteries ===== ===== Installing Batteries =====
  
-The MiTail Battery is a 3.7V, 3000 mAh, 103665 (approximately 10 x 36 x 65 mm) LiPo battery with a "JST PH 2-pin" connector. There are two of them.+The MiTail Battery is a 3.7 V, 3000 mAh, 103665 (approximately 10 x 36 x 65 mm) LiPo battery with a "JST PH 2-pin" connector. There are two of them.
  
 {{ :en:manuals:battery.jpg?nolink&600 |}} {{ :en:manuals:battery.jpg?nolink&600 |}}
Line 133: Line 133:
 </WRAP> </WRAP>
  
-==== pulley Calibration / Resetting Servo Home Position ====+==== Pulley Calibration / Resetting Servo Home Position ====
  
 To do this correctly, first power up the PCB with the new servo attached directly to the board. That will center or "home" the servo before you reattach the pulley. Secondly, make sure the pulley is in the following "ten minutes to the hour" position; the topmost screw head will also align with the servo mount rib below it (note that the servo splines may not line up perfectly and may land a tooth to the left or the right slightly or a particular trail might bias more towards the center screw): To do this correctly, first power up the PCB with the new servo attached directly to the board. That will center or "home" the servo before you reattach the pulley. Secondly, make sure the pulley is in the following "ten minutes to the hour" position; the topmost screw head will also align with the servo mount rib below it (note that the servo splines may not line up perfectly and may land a tooth to the left or the right slightly or a particular trail might bias more towards the center screw):
Line 160: Line 160:
 ===== Charging ===== ===== Charging =====
  
-MiTail requires a USB Power Delivery (USB PD) capable charging adapter. PD charging is only possible using a USB-C to USB-C cable and a USB PD chargers together. Adapters with USB-A output, even with a USB-A to USB-C cable **WILL NOT** charge a MiTail. The adapter should provide at least 9V - almost all PD adapters can. If the adapter's rated power is less than 24W, charging will take around 3 hours.+Some versions of tail-series controller hardware require specific charging support. The version of hardware can be determined by looking at the "About your gear" in The Tail Company App, the "Hardware Version" will  say "MITAIL 3.x", which can be used to determine what kind of charging is required. 
 + 
 + 
 +==== USB Power Delivery (USB PD) ==== 
 + 
 +MiTail hardware versions v3.2 through v3.5 require a USB Power Delivery (USB PD) capable charging adapter. PD charging is only possible using a USB-C to USB-C cable and a USB PD chargers together. Adapters with USB-A output, even with a USB-A to USB-C cable **WILL NOT** charge a MiTail. The adapter should provide at least 9V - almost all PD adapters can. If the adapter's rated power is less than 24W, charging will take around 3 hours.
  
 <WRAP round tip 90%> <WRAP round tip 90%>
-If the MiTail red LED is not "breathing" red, it is not charging!+If the MiTail Red LED is not "breathing" red on a PD-required tail, it is not charging!
 </WRAP> </WRAP>
  
 |  {{ :en:manuals:usb-a_to_usb-c.jpg?nolink&400 |}}  |  {{ :en:manuals:usb-c_to_usb-c.jpg?nolink&400 |}}  |   |  {{ :en:manuals:usb-a_to_usb-c.jpg?nolink&400 |}}  |  {{ :en:manuals:usb-c_to_usb-c.jpg?nolink&400 |}}  |  
-|  This **WILL NOT** charge a MiTail (but will charge an EarGear 2).\\ Even though this is a PD charger, it's using a USB-A to USB-C cable,\\ and the tail and charger can't negotiate.  |  This **WILL** charge a MiTail (and an EarGear 2).\\ This is a PD charger, with a USB-C to USB-C cable.  |  +|  This **WILL NOT** charge a PD-required MiTail (but will charge an EarGear 2).\\ Even though this is a PD charger, it's using a USB-A to USB-C cable,\\ and the tail and charger can't negotiate.  |  This **WILL** charge any MiTail (and an EarGear 2).\\ This is a PD charger, with a USB-C to USB-C cable.  |   
 + 
 + 
 +==== "Plain" USB ==== 
 + 
 +MiTail hardware versions v3.6 onward require a USB charger. Charging can be performed through any USB-C cable (such as the EarGear2 USB-A to USB-C charging cable and charger). Note that on these boards, the Red LED is controlled directly by the battery charger and there is **NO** breathing animation. Instead, the Red LED is constant on when charging, and off when charging is disconnected or when charging is complete.
  
  
Line 173: Line 183:
  
 The following visual indicators are presented by the firmware on the board: The following visual indicators are presented by the firmware on the board:
 +
 +
 +==== Blue LED ====
 +
 +The Blue LED (D4) has five states:
 +
 +  - **Off** when powered off.
 +  - **Blink on-off** when BLE is disconnected.
 +  - **Fade-off** when BLE is disconnected and Autonomous Mode (either iOS Casual Mode or No-phone Mode) is active.
 +  - **Constant on** when BLE is connected.
 +  - **Fade-on** when BLE is connected and Autonomous Mode is active.
 +  - **Blink fast three times** when the button is held for more than 3 seconds (but less than 13), indicates the device is ready to power off when the button is released.
 +  - **Blink fast continuously** when the button is held for more than 13 seconds, indicates the device is ready to factory reset when the button is released.
 +
  
   * Red LED: Slow breathing = tail is charging (when connected to USB PD power).     * Red LED: Slow breathing = tail is charging (when connected to USB PD power).  
Line 182: Line 206:
   * Green LED: ON = USB power is charging batteries. Visible only on the PCB.     * Green LED: ON = USB power is charging batteries. Visible only on the PCB.  
  
-Please make sure the PCB has the latest firmware. Firmware may be updated from The Tail Company app, support Python utility, or directly (e.g. using esptool).+==== Red LED ==== 
 + 
 +For v3.2 through v3.5 tail-series controller hardware, the Red LED (D5) has four states: 
 + 
 +  - **Off** during normal operation. 
 +  - **Breathing** while charging. 
 +  - **Constant on** when charging is complete. 
 +  - **Short flash** on, followed by pause to indicate a low (<= 10%) battery condition. 
 + 
 +For v3.6 tail-series controller hardware, the Red LED (D5) has two states: 
 + 
 +  - **Off** when charging is disconnected and when charging complete. 
 +  - **Constant on** when charging. 
 +   
 +**Note:** Unlike the DIGITAiL, MiTail, and MiTail Mini **can** be used while charging. 
 + 
 + 
 +The Green LED (D8) is only present on v3.2 through v3.5 tail-series controller hardware, and is not visible from outside the device case. The LED is a visual indicator for the ''STAT'' pin of the battery charger: 
 + 
 +  - **Constant on** is charge in progress. 
 +  - **Off** is charge completed. 
 +  - **Blink on-off** indicates a fault condition.