Trace: • service-notes-for-mitail

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:manuals:service-notes-for-mitail [2025/11/02 21:37] – darkgrueen:manuals:service-notes-for-mitail [2025/11/02 21:45] (current) – [Charging] darkgrue
Line 1: Line 1:
 ===== Introduction ===== ===== Introduction =====
  
-These instructions do not purport to cover all details or variations of the product and do not claim to provide for every possible contingency in connection with installation, operation, or maintenance. Self-repairs performed by the customer may lead to damage or loss of your product. Should further information be desired or should particular problems arise which are not covered sufficiently or if repair services are desired, please contact The Tail Company ([[contact@thetailcompany.com]]).+These instructions do not purport to cover all details or variations of the product and do not claim to provide for every possible contingency in connection with installation, operation, or maintenance. Self-repairs performed by the customer may lead to damage or loss of your product. Should further information be desired or if repair services are desired, please contact The Tail Company ([[contact@thetailcompany.com]]).
  
 For the purposes of this manual, “left” and “right” references will refer to the MiTail’s orientation when worn on the body, relative to the wearer. So, the “left” side is the side of the MiTail on the wearer’s left. For the purposes of this manual, “left” and “right” references will refer to the MiTail’s orientation when worn on the body, relative to the wearer. So, the “left” side is the side of the MiTail on the wearer’s left.
Line 114: Line 114:
 </WRAP> </WRAP>
  
-If a fresh servo is being installed, you will first need to modify the replacement servo to remove the mounting tab furthest from the servo shaft (so that it can fit into the case).+If a "fresh" servo (shown in top of photo) is being installed, you will first need to modify the replacement servo to remove the mounting tab furthest from the servo shaft so that it can fit into the case (shown in bottom of photo).
  
 {{ :en:manuals:servo_tab_cut.jpg?400 |}} {{ :en:manuals:servo_tab_cut.jpg?400 |}}
Line 137: Line 137:
 ===== Board-level Repairs and Modifications ===== ===== Board-level Repairs and Modifications =====
  
-The tail PCB uses small surface-mounted components, and is not generally considered a repairable unit (replacements are available for order from The Tail Company).+The tail PCB uses small surface-mounted components, and is not generally considered a repairable unit. Replacements are available for order from The Tail Company.
  
 <WRAP round important 90%> <WRAP round important 90%>
Line 148: Line 148:
 ===== Charging ===== ===== Charging =====
  
-MiTail requires a USB Power Delivery (USB PD) capable charging adapter. PD charging is only possible using a USB-C to USB-C cable and a USB PD chargers together. Adapters with USB-A output, even with a USB-A to USB-C cable will **NOT** charge a MiTail. The adapter should provide at least 9V - almost all PD adapters can. If the adapter's rated power is less than 24W, charging will take around 3 hours.+MiTail requires a USB Power Delivery (USB PD) capable charging adapter. PD charging is only possible using a USB-C to USB-C cable and a USB PD chargers together. Adapters with USB-A output, even with a USB-A to USB-C cable **WILL NOT** charge a MiTail. The adapter should provide at least 9V - almost all PD adapters can. If the adapter's rated power is less than 24W, charging will take around 3 hours.
  
 <WRAP round tip 90%> <WRAP round tip 90%>
Back to top