Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		Previous revision
en:manuals:service-notes-for-eargear-2 [2025/05/26 15:26] – created darkgrueen:manuals:service-notes-for-eargear-2 [2026/03/31 15:38] (current) – darkgrue
Line 4: Line 4:
  
 For the purposes of this manual, “left” and “right” references will refer to the EarGear's orientation when worn on the body, relative to the wearer. So, the “right” side is the side of the EarGear with the control board, and on the wearer’s right. For the purposes of this manual, “left” and “right” references will refer to the EarGear's orientation when worn on the body, relative to the wearer. So, the “right” side is the side of the EarGear with the control board, and on the wearer’s right.
 +
  
 ===== Case Screws ===== ===== Case Screws =====
Line 16: Line 17:
  
 {{:en:manuals:right_ear.jpg?400|}} {{:en:manuals:right_ear.jpg?400|}}
 +
 +
 +===== Installing Batteries =====
 +
 +The EarGear Battery is a single 3.7V 103040 LiPo battery with a "JST PH 2-pin" connector.
 +
 +<WRAP round tip 90%>
 +FAA rules on installed batteries are that devices containing lithium batteries (laptops, phones, and also ears) can be checked, but carry-on is preferred to prevent damage/fire. There is a battery capacity limit generally allowing capacities under 100 Wh. The ears, with a single 4.44 Wh battery, is well under the device capacity limits. Travel rules and restrictions should be reviewed in advance, but the Tail Co devices fall well under realistic limits being an "installed, non-removable battery" and a very modest capacity that should be acceptable anywhere a cellphone or laptop would.
 +</WRAP>
 +
 +The positive lead for the batteries is oriented to the left for J1.
 +
 +The plug can be difficult to remove from the board. It’s suggested to pull out and slightly down towards the board (somewhat of a slight rolling motion) helps the plug release better, instead of pulling straight back.
 +
 +<WRAP round important 90%>
 +Be aware that, although the JST-PH 2.0 connectors used on the batteries and across industry are polarized, the polarity that any one battery is set up for is EXTREMELY RANDOM. Positive and negative should be correctly indicated by red and black wires, but the position of the wires in the connector may not be correct for the MiTail (or whatever device you plan on using the battery in), because there's actually no real standard. Plugging in the battery with the polarity reversed can, depending on a lot of factors, be quite bad for the device and/or battery.
 +</WRAP>
 +
 +
 ===== Installing Servos ===== ===== Installing Servos =====
  
Line 28: Line 48:
 {{ :en:manuals:eargear_board.jpg?nolink&600 |}} {{ :en:manuals:eargear_board.jpg?nolink&600 |}}
  
-Avoid connecting the servos to the LED pins on the end of the header block. These pins are reserved.+Avoid connecting the servos to the pins on the left end of the header block. These pins are not connected. 
 + 
 +Make sure you have no slack pinched between the band and the body of the ears, most of the excess cable goes up in the ear case. 
 + 
 + 
 +==== Servo Calibration / Resetting Servo Home Position ==== 
 + 
 +The servos need to be attached in their home position. To do this correctly, first power up the PCB with the new servo attached directly to the board. That will center or "home" the servo before you reattach the servo. The ear "home" position is the ears are parallel with the band. Ear position may be offset if desired, keeping in mind that the "home" position is the middle of the ear's range of motion. 
  
 +== Copyright 2023-2026 © The Mechanical Tail Company Limited contact@thetailcompany.com. All Rights Reserved. ==
  
-== Copyright 2023-2025 © The Mechanical Tail Company Limited contact@thetailcompany.com. All Rights Reserved. == 
Back to top