Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:dev [2025/09/26 19:58] – darkgrueen:dev [2025/09/26 20:01] (current) – [Firmware Update And Flashing] darkgrue
Line 16: Line 16:
  
  
-==== Legacy Product Command Protocols ====+===== Legacy Command Protocols =====
  
   * [[en:dev:digitail-command-protocol|DIGITAiL Command Protocol]]   * [[en:dev:digitail-command-protocol|DIGITAiL Command Protocol]]
Line 23: Line 23:
  
  
-==== Using a Terminal ====+===== Using a Terminal =====
  
   * [[en:dev:using-a-bluetooth-serial-console-on-your-android-device-to-send-console-commands-to-your-digitail|Using A Bluetooth Serial Console on Your Android Device to Send Console Commands to Your DIGITAiL]]\\    * [[en:dev:using-a-bluetooth-serial-console-on-your-android-device-to-send-console-commands-to-your-digitail|Using A Bluetooth Serial Console on Your Android Device to Send Console Commands to Your DIGITAiL]]\\ 
Line 29: Line 29:
  
  
-==== Firmware Update And Flashing ====+===== Firmware Update And Flashing =====
  
-=== Using OTA ===+==== Using OTA ====
  
 If you need to test an experimental firmware or update outside the official CRUMPET app, there is a facility to update over BLE. If you need to test an experimental firmware or update outside the official CRUMPET app, there is a facility to update over BLE.
Line 41: Line 41:
  
  
-== Hardware Flash ==+==== Hardware Flash ====
  
  
-**Tail-series Boards**+=== Tail-series Boards ===
  
  
Line 57: Line 57:
 **Note:** USB to TTL interfaces are available with 5 V, 3.3 V, or selectable voltage. The ESP32 //must// be used with 3.3 V interfaces //only//! Ensure that your cable or device is configured for 3.3 V before connecting it to the controller board, or your ESP32 may be permanently damaged. **Note:** USB to TTL interfaces are available with 5 V, 3.3 V, or selectable voltage. The ESP32 //must// be used with 3.3 V interfaces //only//! Ensure that your cable or device is configured for 3.3 V before connecting it to the controller board, or your ESP32 may be permanently damaged.
  
-**EarGear Boards**+=== EarGear Boards ===
  
 EarGear 2 can be hardware flashed using the USB-C port on the ears and a PC running Chrome or Edge using the [[https://flash.thetailcompany.com/|TailControl ESP Web Tools]]. EarGear 2 can be hardware flashed using the USB-C port on the ears and a PC running Chrome or Edge using the [[https://flash.thetailcompany.com/|TailControl ESP Web Tools]].
-==== Chat With the Tail Co Development Team Community ====+===== Chat With the Tail Co Development Team Community =====
  
 MiTail, EarGear 2, FlutterWings, and MiTail Mini all have updatable firmware! For details, come and talk to us on our Telegram [[https://t.me/+5XsaunrTpIc4OWI8|Tail Co Gear Dev Chat]]! MiTail, EarGear 2, FlutterWings, and MiTail Mini all have updatable firmware! For details, come and talk to us on our Telegram [[https://t.me/+5XsaunrTpIc4OWI8|Tail Co Gear Dev Chat]]!
Back to top