Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:dev:tailcontrol-command-protocol [2026/03/05 17:50] – [Unbinding] darkgrueen:dev:tailcontrol-command-protocol [2026/07/04 19:44] (current) – darkgrue
Line 15: Line 15:
 The hardware platform uses the "Just Works" Bluetooth Low Energy (BLE) pairing method to connect. If Conference Mode ([[#Conference Mode|see below]]) is used, "Passkey" pairing is used. The hardware platform uses the "Just Works" Bluetooth Low Energy (BLE) pairing method to connect. If Conference Mode ([[#Conference Mode|see below]]) is used, "Passkey" pairing is used.
  
- +==== Device Advertisement ====
-===== Device Advertisement =====+
  
 Device name is one of the following: Device name is one of the following:
Line 50: Line 49:
  
 ===== TailControl Device Indicators ===== ===== TailControl Device Indicators =====
- 
  
 ==== Blue LED ==== ==== Blue LED ====
Line 63: Line 61:
   - **Blink fast three times** when the button is held for more than 3 seconds (but less than 13), indicates the device is ready to power off when the button is released.   - **Blink fast three times** when the button is held for more than 3 seconds (but less than 13), indicates the device is ready to power off when the button is released.
   - **Blink fast continuously** when the button is held for more than 13 seconds, indicates the device is ready to factory reset when the button is released.   - **Blink fast continuously** when the button is held for more than 13 seconds, indicates the device is ready to factory reset when the button is released.
- 
  
 ==== Red LED ==== ==== Red LED ====
Line 85: Line 82:
  
 **Note:** Unlike the DIGITAiL, MiTail, MiTail Mini, and FlutterWings devices **can** be used while charging. **Note:** Unlike the DIGITAiL, MiTail, MiTail Mini, and FlutterWings devices **can** be used while charging.
- 
  
 ==== Green LED ==== ==== Green LED ====
Line 98: Line 94:
  
  
-==== Automatic Actions ====+===== Automatic Actions =====
  
 TailControl will automatically shut down the device if there is no BLE connection for ''currConfig.minsToSleep'' (default 0, [[#Developer Commands (use at own risk)|see below]]) minutes. This behavior is suspended if a PD-capable adapter is attached (to allow for charging and/or operating from a external battery) **OR** if the firmware is compiled with a compile-time option to disable the timer (to facilitate wired serial console control where BLE connectivity is not used). TailControl will automatically shut down the device if there is no BLE connection for ''currConfig.minsToSleep'' (default 0, [[#Developer Commands (use at own risk)|see below]]) minutes. This behavior is suspended if a PD-capable adapter is attached (to allow for charging and/or operating from a external battery) **OR** if the firmware is compiled with a compile-time option to disable the timer (to facilitate wired serial console control where BLE connectivity is not used).
Line 164: Line 160:
  
 ===== RGB LED Commands ===== ===== RGB LED Commands =====
 +
 +All **RGB**''xxx'' pattern commands below (except **RGBOFF**), accept an optional trailing **brightness** parameter, an integer from ''0'' to ''100'' representing the overall brightness of the string in percent (e.g., ''RGBRBW 50''). If omitted, brightness defaults to ''DEFAULT_RGB_BRIGHTNESS'' (100%).
  
 | **RGBOFF** | **RGB** LEDs **OFF**, returns ''OK'' | | **RGBOFF** | **RGB** LEDs **OFF**, returns ''OK'' |
-| **RGBRBO** | **RGB** **R**ain**B**ow pattern, returns ''OK'' | +| **RGBCHS** | **RGB** **CH**a**S**e; theater marquee chase; optionally takes a hue color (in RGB Hexidecimal, otherwise default #7F7F7F is used) (e.g., ''RGBCHS'' [''7F7F7F''] [''brightness'']), returns ''OK'' | 
-| **RGBRB2** | **RGB** **R**ain**B**ow pattern with random sparkly glitter, returns ''OK'' | +| **RGBCLN** | **RGB** **CY**lo**N**; color dot sweeping back and forth, with fading trails; optionally takes a hue color (in RGB Hexidecimal, otherwise default #FF0000 is used) (e.g., ''RGBCLN'' [''FF0000''] [''brightness'']); returns ''OK'' | 
-| **RGBCON** | **RGB** **CON**fetti; random-colored speckles that blink in and fade smoothly, returns ''OK'' | +| **RGBDMO** | **RGB** **DE**m**O**; cycle through all the preceding patterns, changing every 10 seconds (e.g., ''RGBDMO'' [''brightness'']); returns ''OK'' | 
-| **RGBSIN** | **RGB** **SIN**e; a colored dot sweeping back and forth, with fading trails, returns ''OK'' | +| **RGBFDE** | **RGB** **F**a**DE**; fade in/out effect (e.g., ''RGBFDE'' [''brightness'']), returns ''OK'' | 
-| **RGBJUG** | **RGB** **JUG**gle; eight colored dots, weaving in and out of sync with each other, returns ''OK'' | +| **RGBFIR** | **RGB** **FIR**e; fire effect (e.g., ''RGBFIR'' [''brightness'']), returns ''OK'' | 
-| **RGBBPM** | **RGB** **BPM**; colored stripes pulsing at a defined Beats-Per-Minute, returns ''OK'' | +| **RGBRBW** | **RGB** **R**ain**B**o**W** pattern (e.g., ''RGBRBW'' [''brightness'']), returns ''OK'' | 
-| **RGBDMO** | **RGB** **DE**m**O**; cycle through all the preceding patterns, changing every 10 seconds, returns ''OK'' | +| **RGBSLD** | **RGB** **S**o**L**i**D**; display a solid color (in RGB Hexidecimal) on all pixels (e.g., ''RGBSLD FFD700'' [''brightness'']), returns ''OK'' | 
-| **RGBTST** | **RGB** **TE**s**T**; color cycle the first and last pixel of the RGB string (endpoints test), returns ''OK'' | +| **RGBSNO** | **RGB** **SNO**w; snow effect; optionally takes a hue color (in RGB Hexidecimal, otherwise default #FFFFFF is used) (e.g., ''RGBSNO'' [''FFFFFF''] [''brightness'']), returns ''OK'' | 
-| **SETRGB** | **SET** **RGB** configuration; returns ''OK'' and restarts after 3 seconds; (e.g., ''SETRGB 325 12 2900'') [''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |+| **RGBTST** | **RGB** **TE**s**T**; color cycle the first and last pixel of the RGB string (endpoints test) (e.g., ''RGBTST'' [''brightness'']), returns ''OK'' | 
 +| **RGBTWK** | **RGB** **TW**in**K**le; random twinkle effect (e.g., ''RGBTWK'' [''brightness'']), returns ''OK'' | 
 +| **RGBWPE** | **RGB** **W**i**PE**; color wipe (e.g., ''RGBWPE'' [''brightness'']), returns ''OK'' | 
 +| **SETRGB** | **SET** **RGB** configuration; returns ''OK'' and restarts after 3 seconds; (e.g., ''SETRGB 325 12 2900'') [''numRGBLEDs'' ''nomRGBVolt'' ''maxRGBmAmp''] |
  
  
Line 188: Line 189:
 | **STOPNPM** | **STOP** **N**o-**P**hone **M**ode and disables it in NVS configuration; returns ''OK'', followed by ''AUTO END'' | | **STOPNPM** | **STOP** **N**o-**P**hone **M**ode and disables it in NVS configuration; returns ''OK'', followed by ''AUTO END'' |
 | **USERMOVE** | Set user-defined move ([[#User-defined Moves and Glow Tip Patterns|see below]]), returns ''OK'' | | **USERMOVE** | Set user-defined move ([[#User-defined Moves and Glow Tip Patterns|see below]]), returns ''OK'' |
-| **STOPPUSSKEY** | **STOP** **P**a**SSKEY**; disable Conference Mode, returns ''OK'', and restarts after 3 seconds ([[#Conference Mode|see below]]) :!: NOTE THE WARNING UNDER [[#Conference Mode]]!|+| **STOPPUSSKEY** | **STOP** **P**a**SSKEY**; disable Conference Mode, returns ''OK'', and restarts after 3 seconds ([[#Conference Mode|see below]]) |
 | **USERLEDS** | Set user-defined Glow Tip pattern ([[#User-defined Moves and Glow Tip Patterns|see below]]), returns ''OK'' | | **USERLEDS** | Set user-defined Glow Tip pattern ([[#User-defined Moves and Glow Tip Patterns|see below]]), returns ''OK'' |
 | **VER** | Returns the firmware **VER**sion number; (e.g., ''VER 5.0.0''); followed by a line that is either ''GLOWTIP TRUE'' if a Glow Tip is connected, or ''GLOWTIP FALSE'' if one is not; and a final line that is either ''RGB TRUE'' if a RGB LED strip is connected, or ''RGB FALSE'' if it is not | | **VER** | Returns the firmware **VER**sion number; (e.g., ''VER 5.0.0''); followed by a line that is either ''GLOWTIP TRUE'' if a Glow Tip is connected, or ''GLOWTIP FALSE'' if one is not; and a final line that is either ''RGB TRUE'' if a RGB LED strip is connected, or ''RGB FALSE'' if it is not |
Line 196: Line 197:
  
 | **BATT** | **BATT**ery percentage, returns the integer value of estimated battery capacity remaining  (e.g., ''61'') | | **BATT** | **BATT**ery percentage, returns the integer value of estimated battery capacity remaining  (e.g., ''61'') |
-| **READCONF** | **READ** running **CONF**iguration; returns space-delimited running configuration parameters (e.g., ''READCONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] | +| **READCONF** | **READ** running **CONF**iguration; returns space-delimited running configuration parameters (e.g., ''READCONF 1 ABCDEF 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''myColor'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''nomRGBVolt'' ''maxRGBmAmp''] | 
-| **WRITECONF** | **WRITE** **CONF**iguration to NVS and set running configuration to match (e.g., ''WRITECONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''], returns ''OK'' |+| **WRITECONF** | **WRITE** **CONF**iguration to NVS and set running configuration to match (e.g., ''WRITECONF 1 ABCDEF 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''myColor'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''nomRGBVolt'' ''maxRGBmAmp''], returns ''OK'' |
 | **SETDISCONNECTEDCOUNT** | **SET** BLE **DISCONNECTED** power off **COUNT**down parameter in NVS and running configuration (in minutes, ''SETDISCONNECTEDCOUNT 0'' disables automatic poweroff), returns ''OK'' | | **SETDISCONNECTEDCOUNT** | **SET** BLE **DISCONNECTED** power off **COUNT**down parameter in NVS and running configuration (in minutes, ''SETDISCONNECTEDCOUNT 0'' disables automatic poweroff), returns ''OK'' |
 | **SETHOLDONSTOP** | **SET** servo **HOLD** is maintained when the servos **STOP** (maintains servo PWM when not moving, default for EarGear 2); returns ''OK'' | | **SETHOLDONSTOP** | **SET** servo **HOLD** is maintained when the servos **STOP** (maintains servo PWM when not moving, default for EarGear 2); returns ''OK'' |
Line 204: Line 205:
 | **SETLISTENMOVES** | **SET** internal **LISTEN** Mode **MOVES** to play on a listen event in addition to sending event notifications; returns ''OK'' | | **SETLISTENMOVES** | **SET** internal **LISTEN** Mode **MOVES** to play on a listen event in addition to sending event notifications; returns ''OK'' |
 | **UNSETLISTENMOVES** | **UNSET** internal **LISTEN** Mode **MOVES** to play on a listen event, only an event notification will be sent and it is the responsibility of the connected application to send commands to react to events; returns ''OK'' | | **UNSETLISTENMOVES** | **UNSET** internal **LISTEN** Mode **MOVES** to play on a listen event, only an event notification will be sent and it is the responsibility of the connected application to send commands to react to events; returns ''OK'' |
 +| **SETMYCOLOR** | **SET** **MYCOLOR** (in RGB Hexidecimal) to persist in app UI display for this device (e.g., ''SETMYCOLOR FFD700''); returns ''OK'' |
 | **SETTILTMOVES** | **SET** internal **LISTEN** Mode **MOVES** to play on a tilt event in addition to sending event notifications; returns ''OK'' | | **SETTILTMOVES** | **SET** internal **LISTEN** Mode **MOVES** to play on a tilt event in addition to sending event notifications; returns ''OK'' |
 | **UNSETTILTMOVES** | **UNSET** internal **LISTEN** Mode **MOVES** to play on a listen event, only an event notification will be sent and it is the responsibility of the connected application to send commands to react to events; returns ''OK'' | | **UNSETTILTMOVES** | **UNSET** internal **LISTEN** Mode **MOVES** to play on a listen event, only an event notification will be sent and it is the responsibility of the connected application to send commands to react to events; returns ''OK'' |
 | **OTA** | Starts firmware **O**ver **T**he **A**ir update process (e.g., ''OTA <expected size in bytes> <expected MD5>''); returns ''BEGIN OTA'' or ''ERR'' on failure to start, ''OTA SUCCESS'' on success, or ''OTA ERR'' on error during OTA process | | **OTA** | Starts firmware **O**ver **T**he **A**ir update process (e.g., ''OTA <expected size in bytes> <expected MD5>''); returns ''BEGIN OTA'' or ''ERR'' on failure to start, ''OTA SUCCESS'' on success, or ''OTA ERR'' on error during OTA process |
 | **FORMATNVS** | **FORMAT** **NVS** (erase all contents of the default NVS partition, including BLE bonds), returns ''OK'' and reboots after 3 seconds | | **FORMATNVS** | **FORMAT** **NVS** (erase all contents of the default NVS partition, including BLE bonds), returns ''OK'' and reboots after 3 seconds |
-| **READNVS** | **READ** **CONF**iguration from NVS; returns space-delimited configuration parameters stored in NVS (e.g., ''READNVS 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |+| **READNVS** | **READ** **CONF**iguration from NVS; returns space-delimited configuration parameters stored in NVS (e.g., ''READNVS 1 ABCDEF 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''myColor'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''nomRGBVolt'' ''maxRGBmAmp''] |
 | **REBOOT** | **REBOOT**; returns ''OK'' and reboots after 3 seconds | | **REBOOT** | **REBOOT**; returns ''OK'' and reboots after 3 seconds |
 | **TASKU** | Prints to the hardware serial console the minimum amount of remaining stack space that was available to the task since the task started executing (high water mark), returns ''OK'' | | **TASKU** | Prints to the hardware serial console the minimum amount of remaining stack space that was available to the task since the task started executing (high water mark), returns ''OK'' |
Line 234: Line 236:
   * Parameters can be separated by any character that is not a number or a letter (e.g., space, comma, semicolon). However, the letters themselves act as separators, and it is recommended that no additional characters are used, as the serial buffer has a limited capacity and may not be able to store the whole instruction.   * Parameters can be separated by any character that is not a number or a letter (e.g., space, comma, semicolon). However, the letters themselves act as separators, and it is recommended that no additional characters are used, as the serial buffer has a limited capacity and may not be able to store the whole instruction.
   * Depending on the tail and position, it can sag out of the commanded position when servo power is released at the end of the DSSP move. This may cause a visual defect of jerking back into the previous position when the next move starts.   * Depending on the tail and position, it can sag out of the commanded position when servo power is released at the end of the DSSP move. This may cause a visual defect of jerking back into the previous position when the next move starts.
- 
  
 ==== DSSP Example ==== ==== DSSP Example ====
Line 281: Line 282:
  
 {{:en:dev:position_limits_visualization.png?400|}} {{:en:dev:position_limits_visualization.png?400|}}
- 
  
 ==== USERMOVE Examples ==== ==== USERMOVE Examples ====
- 
  
 === Example 1 – Slow Wag 1 (same as the ''TAILS1'' command) === === Example 1 – Slow Wag 1 (same as the ''TAILS1'' command) ===
Line 302: Line 301:
   * **L75L75** Position 2 is reached in 75 * 20 ms = 1.5 s; return to Position 1 in the same time     * **L75L75** Position 2 is reached in 75 * 20 ms = 1.5 s; return to Position 1 in the same time  
   * **H1** Home at end of move   * **H1** Home at end of move
- 
  
 === Example 2 – Test Servos === === Example 2 – Test Servos ===
Line 323: Line 321:
 Because no easing parameters (''E'' or ''F'') are specified, no easing is used by default. Because no easing parameters (''E'' or ''F'') are specified, no easing is used by default.
 </WRAP> </WRAP>
- 
  
 ==== USERLEDS Examples ==== ==== USERLEDS Examples ====
- 
  
 === Example 1 – Beacon (same as the ''LEDBEA'' command) === === Example 1 – Beacon (same as the ''LEDBEA'' command) ===
Line 352: Line 348:
   * **A0A8** Start off, finish at full brightness     * **A0A8** Start off, finish at full brightness  
   * **L100L100** Each brightness point is reached in 100 * 20 ms = 2 s   * **L100L100** Each brightness point is reached in 100 * 20 ms = 2 s
 +
 +
 +===== Autonomous Mode =====
 +
 +Defines a sequence of random moves, selected from any of three groups as below; interval between moves varies randomly
 +from T1 to T2.
 +
 +**AUTOMODE G<n>[G<n> ... [G<n>]] T<nnn>T<nnn>T<nnn>**
 +
 +The tail will select a random move from the specified group(s), pausing for a random number of seconds between each move (min and max specified by the first and second ''T'' parameter, respectively). The tail will stop completely after the time passed by the 3rd ''T'' parameter.
 +
 +Autonomous Mode is ended (after completing any ongoing move) if a BLE connection is made.
 +
 +^ Group  ^ Move Group Name  ^ Move List  ^
 +| 1 | Calm and Relaxed | Slow Wag 1, Slow Wag 2, Slow Wag 3 |
 +| 2 | Fast and Excited | Fast Wag, Short Wag, Happy Wag, Erect |
 +| 3 | Frustrated and Tense | Tremble 1, Tremble 2, Tremble Erect, High Wag |
 +
 +The parameter order is not important, except that the three ''T'' parameters are interpreted in the order specified below.
 +
 +^ Prefix  ^ Parameter Type  ^ Range of Values  ^
 +| **G** | Move Group (see table above) | <1 ... 3> |
 +| **T1** | Minimum random pause between moves in 1-second increments | <1 ... 240> (1 s ... 4 min) |
 +| **T2** | Maximum random pause between moves in 1-second increments | <1 ... 240> (1 s ... 4 min) |
 +| **T3** | Total duration in 15-second increments | <1 ... 240> (15 s ... 60 min); <251 ... 254> are reserved, see [[en:dev:tailcontrol-command-protocol#no-phone_mode|No-phone Mode]], below) |
 +
 +**STOPAUTO**
 +
 +''STOPAUTO'' will abort the current Autonomous Mode after completing any ongoing move.
  
  
Line 364: Line 389:
 <WRAP round important 90%> <WRAP round important 90%>
 Do **NOT** attempt to use Conference Mode on TailControl firmware prior to 5.3.0, or a condition requiring repair of the control board can occur.</WRAP> Do **NOT** attempt to use Conference Mode on TailControl firmware prior to 5.3.0, or a condition requiring repair of the control board can occur.</WRAP>
- 
- 
 ==== Enabling Conference Mode (Pairing and Binding) ==== ==== Enabling Conference Mode (Pairing and Binding) ====
  
Line 373: Line 396:
  
 The device will then reboot after 3 seconds. Conference Mode is then enabled, and pairing proceeds. The user's phone (or other device) will prompt for the passkey (which was set earlier), and the bond will be established on both devices. After that, the passkey or a previous bond (up to 3 can be stored) will be required to connect to the device. The device will then reboot after 3 seconds. Conference Mode is then enabled, and pairing proceeds. The user's phone (or other device) will prompt for the passkey (which was set earlier), and the bond will be established on both devices. After that, the passkey or a previous bond (up to 3 can be stored) will be required to connect to the device.
- 
  
 ==== Disabling Conference Mode ==== ==== Disabling Conference Mode ====
Line 382: Line 404:
  
 The device will then reboot after 3 seconds. If the bond needs to be removed or reset, see [[en:dev:tailcontrol-command-protocol#unbinding|Unbinding]], below. The device will then reboot after 3 seconds. If the bond needs to be removed or reset, see [[en:dev:tailcontrol-command-protocol#unbinding|Unbinding]], below.
- 
  
 ==== Unbinding ==== ==== Unbinding ====
Line 391: Line 412:
  
   * Sending a ''FORMATNVS'' command to the TailControl console. This will factory-reset and reboot.   * Sending a ''FORMATNVS'' command to the TailControl console. This will factory-reset and reboot.
-  * Performing a factory reset using the single button (TailControl v5.1.0, forward):+  * Performing a factory reset using the single button:
       - Press and hold the power button.       - Press and hold the power button.
       - At approximately 3 seconds, the blue LED will flash three times and turn off. Continue to hold without releasing the button. If you wish to cancel the factory reset, release at any time before the next step and the device will power off.       - At approximately 3 seconds, the blue LED will flash three times and turn off. Continue to hold without releasing the button. If you wish to cancel the factory reset, release at any time before the next step and the device will power off.
Line 403: Line 424:
  
 </WRAP> </WRAP>
 +
 +
 +===== iOS Casual Mode =====
 +
 +<WRAP round todo 90%>
 +This feature is pending removal in a future release.
 +</WRAP>
 +
 +Because the CRUMPET application is not currently permitted to manage the tail while the iOS application is in the background, the application uses the ''AUTOMODE'' command to have the tail emulate the Casual Mode behavior on-board the tail (Note there is a typo in the string the iOS app sends: there is no space between the command and the first parameter):
 +
 +**AUTOMODEG1  T15 T100 T240**
 +
 +Note that the ''G'' and the first two ''T'' parameters will depend on the selections made in the app.
 +
 +Important! The minimum random pause cannot be less that 15 seconds.
 +
 +==== iOS Casual Mode Example ====
 +
 +**AUTOMODE T15T60T240 G1G2**
 +
 +  * **T15** 15-second minimum random pause between moves
 +  * **T60** 60-second (1 minute) maximum random pause between moves
 +  * **T240** 3600-second (240 * 15 = 3600 s = 1 hour) total duration of Autonomous Mode
 +  * **G1G2** Randomly select a move from groups 1 and 2
  
  
Line 419: Line 464:
 ===== No-phone Mode ===== ===== No-phone Mode =====
  
-Perform random moves while disconnected from a BLE client, selected from any of three groups as below; interval between moves varies randomly from T1 to T2. This feature is comparable to Casual Mode in the app.+No-phone mode is a feature exclusive of MiTail firmware 4.0.0 or greater or TailControl.
  
-**AUTOMODE G<n>[G<n>[G<n>]] T<1 ... 240>T<1 ... 240>T<251 ... 254>** +**AUTOMODE G<n>[G<n>[G<n>]] T<nnn>T<nnn>T<251 ... 254>**
- +
-The tail will select a random move from the specified group(s), pausing for a random number of seconds between each move (min and max specified by the first and second ''T'' parameter, respectively). The tail will stop completely after the time passed by the 3rd ''T'' parameter. +
- +
-No-phone Mode is suspended (after completing any ongoing move) if a BLE connection is made. It will resume after BLE is disconnected. +
- +
-^ Group  ^ Move Group Name  ^ Move List  ^ +
-| 1 | Calm and Relaxed | Slow Wag 1, Slow Wag 2, Slow Wag 3 | +
-| 2 | Fast and Excited | Fast Wag, Short Wag, Happy Wag, Erect | +
-| 3 | Frustrated and Tense | Tremble 1, Tremble 2, Tremble Erect, High Wag | +
- +
-The parameter order is not important, except that the three ''T'' parameters are interpreted in the order specified below. +
- +
-^ Prefix  ^ Parameter Type  ^ Range of Values  ^ +
-| **G** | Move Group (see table above) | <1 ... 3> | +
-| **T1** | Minimum random pause between moves in 1-second increments | <1 ... 240> (1 s ... 4 min) | +
-| **T2** | Maximum random pause between moves in 1-second increments | <1 ... 240> (1 s ... 4 min) | +
-| **T3** | Delay to wait for BLE connection before starting NPM | <25**1** ... 25**4**> (1 ... 4 min) |+
  
 No-phone Mode (NPM) will cause the tail to delay one to four minutes (based on the setting of the third ''T'' parameter of 25**1** through 25**4**) to wait for a BLE connection. If no BLE connection is made during that time, the tail will select a random move from the specified group(s), pausing for a random number of seconds between each move (min and max specified by the first and second ''T'' parameter, respectively). No-phone Mode (NPM) will cause the tail to delay one to four minutes (based on the setting of the third ''T'' parameter of 25**1** through 25**4**) to wait for a BLE connection. If no BLE connection is made during that time, the tail will select a random move from the specified group(s), pausing for a random number of seconds between each move (min and max specified by the first and second ''T'' parameter, respectively).
Line 447: Line 475:
  
 Stops No-phone mode and disables it in NVS configuration. Stops No-phone mode and disables it in NVS configuration.
- 
- 
-==== No-phone Mode Example ==== 
- 
-**AUTOMODE T15T60T243 G1G2** 
- 
-  * **T15** 15-second minimum random pause between moves 
-  * **T60** 60-second (1 minute) maximum random pause between moves 
-  * **T240** 3600-second (240 * 15 = 3600 s = 1 hour) total duration of Autonomous Mode 
-  * **G1G2** Randomly select a move from groups 1 and 2 
  
  
Line 466: Line 484:
  
  
-== Copyright 2024-2025 © The Mechanical Tail Company Limited contact@thetailcompany.com. All Rights Reserved. The Mechanical Tail Company Limited also claims trademark rights in the following: TailControl, MiTail, MiTail Mini, FlutterWings, and EarGear.  Any unauthorized use is expressly prohibited. ==+== Copyright 2024-2026 © The Mechanical Tail Company Limited contact@thetailcompany.com. All Rights Reserved. The Mechanical Tail Company Limited also claims trademark rights in the following: TailControl, MiTail, MiTail Mini, FlutterWings, and EarGear.  Any unauthorized use is expressly prohibited. ==