Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:dev:tailcontrol-command-protocol [2025/09/06 19:36] – [Developer Commands (use at own risk)] darkgrueen:dev:tailcontrol-command-protocol [2025/09/06 22:08] (current) – [Developer Commands (use at own risk)] darkgrue
Line 196: Line 196:
 | **SETHOME** | **SET** **HOME** position (0 through 8) for each servo (e.g., ''SETHOME 4 4''), NOTE: only available on FlutterWings, and EarGear 2; returns ''OK'' | | **SETHOME** | **SET** **HOME** position (0 through 8) for each servo (e.g., ''SETHOME 4 4''), NOTE: only available on FlutterWings, and EarGear 2; returns ''OK'' |
 | **OTA** | Starts firmware **O**ver **T**he **A**ir update process (e.g., ''OTA <expected size in bytes> <expected MD5>''); returns ''BEGIN OTA'' or ''ERR'' on failure to start, ''OTA SUCCESS'' on success, or ''OTA ERR'' on error during OTA process | | **OTA** | Starts firmware **O**ver **T**he **A**ir update process (e.g., ''OTA <expected size in bytes> <expected MD5>''); returns ''BEGIN OTA'' or ''ERR'' on failure to start, ''OTA SUCCESS'' on success, or ''OTA ERR'' on error during OTA process |
-| **FORMATNVS** | **FORMAT** **NVS** (erase all contents of the default NVS partition, including BLE bonds) and reboot |+| **FORMATNVS** | **FORMAT** **NVS** (erase all contents of the default NVS partition, including BLE bonds), returns ''OK'' and reboots after 3 seconds |
 | **READNVS** | **READ** **CONF**iguration from NVS; returns space-delimited configuration parameters stored in NVS (e.g., ''READNVS 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] | | **READNVS** | **READ** **CONF**iguration from NVS; returns space-delimited configuration parameters stored in NVS (e.g., ''READNVS 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |
 | **REBOOT** | **REBOOT**; returns ''OK'' and reboots after 3 seconds | | **REBOOT** | **REBOOT**; returns ''OK'' and reboots after 3 seconds |
Line 380: Line 380:
 **SETPUSSKEY <nnnnnn>** **SETPUSSKEY <nnnnnn>**
  
-The device will then reboot in 3 seconds. Conference Mode is then enabled, and pairing proceeds. The user's phone (or other device) will prompt for the passkey (which was set earlier), and the bond will be established on both devices. After that, the passkey or a previous bond (up to 3 can be stored) will be required to connect to the device.+The device will then reboot after 3 seconds. Conference Mode is then enabled, and pairing proceeds. The user's phone (or other device) will prompt for the passkey (which was set earlier), and the bond will be established on both devices. After that, the passkey or a previous bond (up to 3 can be stored) will be required to connect to the device.
  
 ==== Disabling Conference Mode ==== ==== Disabling Conference Mode ====
Line 388: Line 388:
 **STOPPUSSKEY** **STOPPUSSKEY**
  
-The device will then reboot in 3 seconds. If the bond needs to be removed or reset, see [[en:dev:tailcontrol-command-protocol#unbinding|Unbinding]], below.+The device will then reboot after 3 seconds. If the bond needs to be removed or reset, see [[en:dev:tailcontrol-command-protocol#unbinding|Unbinding]], below.
  
 ==== Unbinding ==== ==== Unbinding ====
Line 399: Line 399:
   * Performing a factory reset using the single button:   * Performing a factory reset using the single button:
       - Press and hold the power button.       - Press and hold the power button.
-      - At approximately 3 seconds, the blue LED will flash three times and turn off. Continue to hold without releasing the button. If you Wish to cancel the factory reset, release at any time before the next step and the device will power off.+      - At approximately 3 seconds, the blue LED will flash three times and turn off. Continue to hold without releasing the button. If you wish to cancel the factory reset, release at any time before the next step and the device will power off.
       - Ten seconds after the triple-flash (13 seconds total of continuous holding), the blue LED will blink quickly continuously, release to perform the factory reset. The blue LED will go solid, then the ESP will restart, with the blue LED flashing slowly (ready to connect).       - Ten seconds after the triple-flash (13 seconds total of continuous holding), the blue LED will blink quickly continuously, release to perform the factory reset. The blue LED will go solid, then the ESP will restart, with the blue LED flashing slowly (ready to connect).
  
Back to top