Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:dev:tailcontrol-command-protocol [2025/06/16 23:26] – [Developer Commands (use at own risk)] darkgrueen:dev:tailcontrol-command-protocol [2025/06/21 14:27] (current) – [Conference Mode] darkgrue
Line 191: Line 191:
 | **READCONF** | **READ** running **CONF**iguration; returns space-delimited running configuration parameters (e.g., ''READCONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] | | **READCONF** | **READ** running **CONF**iguration; returns space-delimited running configuration parameters (e.g., ''READCONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |
 | **WRITECONF** | **WRITE** **CONF**iguration to NVS and set running configuration to match (e.g., ''WRITECONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900''), returns ''OK'' [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] | | **WRITECONF** | **WRITE** **CONF**iguration to NVS and set running configuration to match (e.g., ''WRITECONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900''), returns ''OK'' [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |
-| **SETDISCONNECTEDCOUNT** | **SET** BLE **DISCONNECTED** power off **COUNT**down parameter in NVS and running configuration (in minutes, ''0'' disables automatic poweroff), returns ''OK'' |+| **SETDISCONNECTEDCOUNT** | **SET** BLE **DISCONNECTED** power off **COUNT**down parameter in NVS and running configuration (in minutes, ''SETDISCONNECTEDCOUNT 0'' disables automatic poweroff), returns ''OK'' |
 | **SETHOLDONSTOP** | **SET** servo **HOLD** is maintained when the servos **STOP** (maintains servo PWM when not moving, default for EarGear 2); returns ''OK'' | | **SETHOLDONSTOP** | **SET** servo **HOLD** is maintained when the servos **STOP** (maintains servo PWM when not moving, default for EarGear 2); returns ''OK'' |
 | **UNSETHOLDONSTOP** | **UNSET** servo **HOLD** when the servos **STOP** (servo PWM is dropped when not moving, default for tail-based devices); returns ''OK'' | | **UNSETHOLDONSTOP** | **UNSET** servo **HOLD** when the servos **STOP** (servo PWM is dropped when not moving, default for tail-based devices); returns ''OK'' |
Line 372: Line 372:
   * **Replay Attack:** a type of network attack in which an attacker captures a valid network transmission and then retransmits it later. The main objective is to trick the system into accepting the retransmission of the data as legitimate.   * **Replay Attack:** a type of network attack in which an attacker captures a valid network transmission and then retransmits it later. The main objective is to trick the system into accepting the retransmission of the data as legitimate.
  
 +<WRAP round important 90%>
 +Do NOT attempt to use Conference Mode on TailControl firmware prior to 5.3.0, or a condition requiring repair of the control board can occur.</WRAP>
 ==== Enabling Conference Mode (Pairing and Binding) ==== ==== Enabling Conference Mode (Pairing and Binding) ====
  
Back to top