Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:dev:tailcontrol-command-protocol [2025/06/13 23:53] – darkgrueen:dev:tailcontrol-command-protocol [2025/06/21 14:27] (current) – [Conference Mode] darkgrue
Line 180: Line 180:
 | **STOPAUTO** | **STOP AUTO**nomous Mode, returns ''OK'', followed by ''AUTO END'' | | **STOPAUTO** | **STOP AUTO**nomous Mode, returns ''OK'', followed by ''AUTO END'' |
 | **STOPNPM** | **STOP** **N**o-**P**hone **M**ode and disables it in NVS configuration; returns ''OK'', followed by ''AUTO END'' | | **STOPNPM** | **STOP** **N**o-**P**hone **M**ode and disables it in NVS configuration; returns ''OK'', followed by ''AUTO END'' |
-| **USERMOVE** | Set user-defined move ([[#User-defined Moves and Glow Tip Patterns|See below]]), returns ''OK'' |+| **USERMOVE** | Set user-defined move ([[#User-defined Moves and Glow Tip Patterns|see below]]), returns ''OK'' |
 | **STOPPUSSKEY** | **STOP** **P**a**SSKEY**, disable Conference Mode and restart after 3 seconds ([[#Conference Mode|see below]]), returns ''OK'' | | **STOPPUSSKEY** | **STOP** **P**a**SSKEY**, disable Conference Mode and restart after 3 seconds ([[#Conference Mode|see below]]), returns ''OK'' |
-| **USERLEDS** | Set user-defined Glow Tip pattern ([[#User-defined Moves and Glow Tip Patterns|See below]]), returns ''OK'' |+| **USERLEDS** | Set user-defined Glow Tip pattern ([[#User-defined Moves and Glow Tip Patterns|see below]]), returns ''OK'' |
 | **VER** | Returns the firmware **VER**sion number; ''VER x.x.x''; followed by a line that is either ''GLOWTIP TRUE'' if a Glow Tip is connected, or ''GLOWTIP FALSE'' if one is not; and a final line that is either ''RGB TRUE'' if a RGB LED strip is connected, or ''RGB FALSE'' if it is not | | **VER** | Returns the firmware **VER**sion number; ''VER x.x.x''; followed by a line that is either ''GLOWTIP TRUE'' if a Glow Tip is connected, or ''GLOWTIP FALSE'' if one is not; and a final line that is either ''RGB TRUE'' if a RGB LED strip is connected, or ''RGB FALSE'' if it is not |
  
Line 189: Line 189:
  
 | **BATT** | **BATT**ery percentage, returns the integer value of estimated battery capacity remaining  (e.g., ''61'') | | **BATT** | **BATT**ery percentage, returns the integer value of estimated battery capacity remaining  (e.g., ''61'') |
 +| **READCONF** | **READ** running **CONF**iguration; returns space-delimited running configuration parameters (e.g., ''READCONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |
 +| **WRITECONF** | **WRITE** **CONF**iguration to NVS and set running configuration to match (e.g., ''WRITECONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900''), returns ''OK'' [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |
 +| **SETDISCONNECTEDCOUNT** | **SET** BLE **DISCONNECTED** power off **COUNT**down parameter in NVS and running configuration (in minutes, ''SETDISCONNECTEDCOUNT 0'' disables automatic poweroff), returns ''OK'' |
 +| **SETHOLDONSTOP** | **SET** servo **HOLD** is maintained when the servos **STOP** (maintains servo PWM when not moving, default for EarGear 2); returns ''OK'' |
 +| **UNSETHOLDONSTOP** | **UNSET** servo **HOLD** when the servos **STOP** (servo PWM is dropped when not moving, default for tail-based devices); returns ''OK'' |
 +| **SETHOME** | **SET** **HOME** position (0 through 8) for each servo (e.g., ''SETHOME 4 4''), NOTE: only available on FlutterWings, and EarGear 2; returns ''OK'' |
 +| **OTA** | Starts firmware **O**ver **T**he **A**ir update process (e.g., ''OTA <expected size in bytes> <expected MD5>''); returns ''BEGIN OTA'' or ''ERR'' on failure to start, ''OTA SUCCESS'' on success, or ''OTA ERR'' on error during OTA process |
 | **FORMATNVS** | **FORMAT** **NVS** (erase all contents of the default NVS partition, including BLE bonds) and reboot | | **FORMATNVS** | **FORMAT** **NVS** (erase all contents of the default NVS partition, including BLE bonds) and reboot |
-| **OTA** | Starts firmware **O**ver **T**he **A**ir update process (e.g., ''OTA <expected size in bytes> <expected MD5>''); returns ''BEGIN OTA'' or ''ERR'' on failure to start, ''OTA SUCCESS'' on success, or ''OTA ERR'' on error during OTA process | 
-| **READCONF** | **READ** running **CONF**iguration; returns space-delimited running configuration parameters (e.g., ''READCONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] | 
 | **READNVS** | **READ** **CONF**iguration from NVS; returns space-delimited configuration parameters stored in NVS (e.g., ''READNVS 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] | | **READNVS** | **READ** **CONF**iguration from NVS; returns space-delimited configuration parameters stored in NVS (e.g., ''READNVS 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900'') [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] |
 | **REBOOT** | **REBOOT** after 3 seconds, returns ''OK'' | | **REBOOT** | **REBOOT** after 3 seconds, returns ''OK'' |
-| **RELEASEHOLDONSTOP** | **RELEASE** servo **HOLD** when the servos **STOP** (default for tail-based devices); returns ''OK'' | 
-| **SETHOLDONSTOP** | **SET** servo **HOLD** is maintained when the servos **STOP** (default for EarGear 2); returns ''OK''' | 
-| **SETHOME** | **SET** **HOME** position (0 through 8) for each servo (e.g., ''SETHOME 4 4''), NOTE: only available on FlutterWings, and EarGear 2; returns ''OK'' | 
 | **TASKU** | Prints to the hardware serial console the minimum amount of remaining stack space that was available to the task since the task started executing (high water mark), returns ''OK'' | | **TASKU** | Prints to the hardware serial console the minimum amount of remaining stack space that was available to the task since the task started executing (high water mark), returns ''OK'' |
-| **WRITECONF** | **WRITE** **CONF**iguration to NVS and set running configuration to match (e.g., ''WRITECONF 1 5 0 15 40 3 8 0 0 1 3 0 1 0 1 1 495974 325 12 2900''), returns ''OK'' [''ver'' ''minsToSleep'' ''minsToNPM'' ''minNPMPauseSec'' ''maxNPMPauseSec'' ''groupsNPM'' ''servo1home'' ''servo2home'' ''listenModeNPMEnabled'' ''listenModeResponseOnly'' ''groupsLM'' ''tiltModeNPMEnabled'' ''tiltModeResponseOnly'' ''disconnectedCountdownEnabled'' ''homeOnAppPoweroff'' ''conferenceModeEnabled'' ''securityPasskey'' ''numRGBLEDs'' ''maxRGBVolt'' ''maxRGBmAmp''] | 
- 
 ===== Directly Set Servo Position ===== ===== Directly Set Servo Position =====
  
Line 372: Line 372:
   * **Replay Attack:** a type of network attack in which an attacker captures a valid network transmission and then retransmits it later. The main objective is to trick the system into accepting the retransmission of the data as legitimate.   * **Replay Attack:** a type of network attack in which an attacker captures a valid network transmission and then retransmits it later. The main objective is to trick the system into accepting the retransmission of the data as legitimate.
  
 +<WRAP round important 90%>
 +Do NOT attempt to use Conference Mode on TailControl firmware prior to 5.3.0, or a condition requiring repair of the control board can occur.</WRAP>
 ==== Enabling Conference Mode (Pairing and Binding) ==== ==== Enabling Conference Mode (Pairing and Binding) ====
  
Back to top